Allens performance
10 posts
• Page 1 of 1
Allens performance
Hello,
I'm thinking about sending them my 29mm smoothbores for a full refurb has anyone used them?
I'm thinking about sending them my 29mm smoothbores for a full refurb has anyone used them?
-
rsvfletch
- Posts: 20
- Joined: Tue Nov 27, 2012 10:32 am
- Location: Wistaston Cheshire
There very good ..but get a quote of them 1st as a lot of the parts are £££....
Dept on what problem you have with the cabs.....?
As a simple strip and ultra sonic clean will cost a lot less.....guy on OSS does it
Dept on what problem you have with the cabs.....?
As a simple strip and ultra sonic clean will cost a lot less.....guy on OSS does it
-
Duckndive
- ACS
- Posts: 93
- Joined: Sun Nov 25, 2012 9:22 pm
Hi I've spoken to mcmental off OSS but I'd like them sorting out as I've been having an issue that seems to be fuel related. It runs fine til I rev it hard then it splutters and seems to drop onto 3 cylinders as if it's running out of fuel. I've done the float heights got a high flow tap etc. dyna ignition and coils fitted valve clearance and compression ok so I'm looking to take the carbs out of the equation.
-
rsvfletch
- Posts: 20
- Joined: Tue Nov 27, 2012 10:32 am
- Location: Wistaston Cheshire
I agree with the Ultrasonic route myself. Do that first and see if the situation improves. From experience, I have VM33 smoothies, i can tell you parts are very expensive. Possibly even think about some Dyno time as well once you happy they are sorted, just to make sure the fuelling is exactly where it should be.
JOnboy

JOnboy

-
jonboy
- ACS
- Posts: 56
- Joined: Mon Nov 26, 2012 9:08 am
- Location: Hatt, Cornwall, England
Talking of dyno testing who's recommended? I'm in the Crewe area
-
rsvfletch
- Posts: 20
- Joined: Tue Nov 27, 2012 10:32 am
- Location: Wistaston Cheshire
rsvfletch wrote:Hello,
I'm thinking about sending them my 29mm smoothbores for a full refurb has anyone used them?
I sent my 28mm mikunis to Allens earlier this yr after a local Dinoman snapped of 2 air screws the ones under float bowls,got them back 3.5months later and a bill £330....
so you've been warned......
-
Gshub
- Posts: 23
- Joined: Mon Nov 26, 2012 5:58 pm
- Location: in the middle of the Norfolk country side.....
Oh dear sounds like an expensive one off
-
rsvfletch
- Posts: 20
- Joined: Tue Nov 27, 2012 10:32 am
- Location: Wistaston Cheshire
rsvfletch wrote:Oh dear sounds like an expensive one off
if you only you new half the storey

Im leaving it there as it took two summers of not riding Gs, but its been sorted now by a good a good Dynoman.....
and he is close to where we live now, www.seastarsuperbikes.co.uk,the only bikeshop that I will use localy ever again

roll on the spring I got alota catching up to do,any excuse to ride I will this summer...............
-
Gshub
- Posts: 23
- Joined: Mon Nov 26, 2012 5:58 pm
- Location: in the middle of the Norfolk country side.....
Thanks for that they're not a million miles away I'll speak to them when I'm ready.
-
rsvfletch
- Posts: 20
- Joined: Tue Nov 27, 2012 10:32 am
- Location: Wistaston Cheshire
rsvfletch wrote:Thanks for that they're not a million miles away I'll speak to them when I'm ready.
They might sell Dukes and new Kwaks they had a open day in the summer,took Gs there if though it wasnt running to well alot of people were having more of a look at my bike than all the new one

Also been told Graham Dances SSB bike is some time put on their Dyno ,he is a old m8 of mine

-
Gshub
- Posts: 23
- Joined: Mon Nov 26, 2012 5:58 pm
- Location: in the middle of the Norfolk country side.....
10 posts
• Page 1 of 1
Who is online
Users browsing this forum: No registered users and 3 guests