My new turbo Kat project

by **FBJ admin** » Wed Dec 12, 2012 9:54 pm

One of my pics. Done a while back now :-)

by **FBJ admin** » Wed Dec 12, 2012 10:06 pm

Another one, in Strangewayz jig

by **FBJ admin** » Wed Dec 12, 2012 10:09 pm

i love how he shaped the ends

by **BEERBELLYKELLY** » Thu Dec 13, 2012 9:12 pm

FFS alan get some fekkin hammerite on ruppertons frame jig !!! is it your round for guinn ?

by **dixiethedog** » Fri Dec 14, 2012 8:02 pm

Ive always enjoyed seeing Strangewayz frame work.

Ive managed to get a load of pics from OSS of his EFE project,before the site vanished. Very inspirational.

by **FBJ admin** » Sat Dec 15, 2012 11:40 pm

I'm after a HSR42, may by a new one, they are on ebay for Harleys, will they run on the draw thru, or do I need a specific turbo HSR?

Next question

wheres the best place to get mt straight cuts from, or shall I just leave it to Roger to source the bits then fit them?

Think I'm gonna have a big clean up in the garage tomorrow and get the motor in the bench for stripping, ready for rebuild.

Cheers

by **Duckndive** » Sun Dec 16, 2012 12:30 am

FBJ admin wrote:I'm after a HSR42, may by a new one, they are on ebay for Harleys, will they run on the draw thru, or do I need a specific turbo HSR?

Cheers

The Ditch Pump Carb kits come with a 160 main....

you just need to swop the needle for the richer one and change the main to a 220 or larger ...

You have to drill after 220........Allens have the needle and jet / s you can change the pilot as well...

Fruit Loop will point u in the right direction............. :roll:

by **dixiethedog** » Sun Dec 16, 2012 4:39 pm

I might be tempted to sell my mikuni HSR42 if your interested?? I bought it off Yantosh (via FBM i think?),it came from the Big CC katana 1500 turbo that i believe Dave Buttery raced?
Im not depserate to sell,but if it helps to get your bike done,im sure a deal could be done?? I paid 150 for it,so id need that back plus postage. Mail me if your interested?
Otherwise,its staying put,until i pull me finger out and get my EFE turbo'd.

If I sell,id just wait until i need one and buy another.

by **FBJ admin** » Sun Dec 16, 2012 6:00 pm

Duckndive wrote:
FBJ admin wrote:I'm after a HSR42, may by a new one, they are on ebay for Harleys, will they run on the draw thru, or do I need a specific turbo HSR?

Cheers

The Ditch Pump Carb kits come with a 160 main....

you just need to swop the needle for the richer one and change the main to a 220 or larger ...

You have to drill after 220........Allens have the needle and jet / s you can change the pilot as well...

Fruit Loop will point u in the right direction.............

So is ditch pump a nick name for a hsr, sorry to be dumb never had a turbo bike. Did av a hsr on my old fxdx. So if i get one second hand il neex the needle and a jet. I will go on allens site to get a quoteon the bits. They seem to be about £250 new.
Dixiedog. Thanks for the offer bud. I will see how much it will cost for the requirex parts tben let you know. Might buy a new one as it might come with various required bits including jets

by **dixiethedog** » Sun Dec 16, 2012 8:01 pm

Yeah,no bother FBJ,let me know if your interested? I figure with it being from big cc,it should be set up pretty well for a turbo.